2000L Tanks Screw Air Compressor Air Receiver Tank

2000L Compressed Air Tanks Screw Air Compressor Carbon Steel Air Receiver Tank

Product Overview

A 2000L carbon steel air receiver is a large-capacity compressed air storage vessel designed for rotary screw compressor systems in factories, workshops, power stations, bottling lines, automotive plants, textile mills, woodworking facilities, pneumatic automation lines, and central compressed air stations. With 2.0m³ storage, the tank works as a buffer between the screw airend and the plant distribution network. It stores compressed air, absorbs peak demand, reduces load/unload cycling of fixed-speed screw compressors, stabilizes header pressure, cools saturated discharge air, separates bulk condensate, and protects downstream filters, refrigerated dryers, and adsorption dryers.

Carbon steel is the most common construction material for 2000L industrial receivers because it offers high strength, economical fabrication, and good service life when properly coated, galvanized, or lined. For 2000L screw systems, typical working pressures include 8bar, 10bar, 13bar, and 16bar, with vertical and horizontal versions available. A standard vertical 2000L tank at 8bar may have approximately 1000mm internal diameter, 2860mm overall height, and 370kg empty weight; 10bar versions are around 390kg and 13bar versions around 465kg, while actual values change with steel grade, head type, coating, and nozzle configuration . Horizontal 2000L tanks are used for low-ceiling rooms, outdoor foundations, trailer skids, and sites where a lower center of gravity is preferred.

Working Principle Of A 2000L Screw Receiver

Compressed air leaves the screw compressor hot and saturated. After the aftercooler and moisture separator, it enters the receiver. Because the 2000L vessel provides a large cross-section, internal velocity drops sharply. Lower velocity, longer residence time, and lower temperature produce four main effects:

1. Thermal stabilization:​ Air temperature approaches ambient. Cooling condenses part of the water vapor into liquid water.

2. Gravity separation:​ Free water, oil mist, and coarse particles settle toward the bottom. Automatic or manual drains remove the liquid before it reaches filters and dryers.

3. Pressure buffering:​ Stored air expands when demand exceeds screw output and is recharged when demand falls. The receiver decouples compressor supply from instantaneous consumption.

4. Pulse and cycle control:​ For fixed-speed screw machines, the large 2000L volume extends load/unload time, reduces starts, and improves compressor reliability. For variable-speed drives, the tank supports pressure stability during ramp changes and short peaks.

In a wet receiver arrangement, the 2000L tank is installed before the dryer to cool air and drop bulk condensate. In a dry receiver arrangement, the tank is installed after the dryer to store treated air. Central screw plants often use a 2000L wet receiver before treatment and an additional 1000L or 2000L dry receiver after treatment.

Sizing Method For 2000L Receivers

Two methods are used for screw compressor receiver selection.

Quick percentage rule: for fixed-speed rotary screw compressors with reasonably stable demand, start with receiver volume equal to approximately 10–20 percent of free air delivery; 10–15 percent is common for stable load and 15–20 percent or higher for fluctuating load . A 2000L tank corresponds roughly to:

• About 10m³/min FAD at 20 percent rule

• About 13–20m³/min FAD at 10–15 percent rule

• Larger screw systems with strong peaks may use 2000L as wet storage plus additional dry storage

For variable-speed screw compressors, storage can often be 50–70 percent of the fixed-speed volume because the inverter modulates flow continuously, but peak events, long pipelines, and dryer buffering may still require 2000L .

Pressure-swing formula for peak buffering:

V = (Q × t × Pₐ) / (P₁ − P₂)

V = receiver volume in liters or consistent units

Q = excess peak demand above compressor output during the event

t = event duration

Pₐ = atmospheric pressure, 1.013bar absolute

P₁ = cut-out pressure absolute

P₂ = cut-in pressure absolute

Worked example A, 8bar system: screw compressor delivers 12m³/min. Peak demand is 14m³/min for 30 seconds. Allowable swing from 8.0bar cut-out to 6.0bar cut-in.

Q = 2m³/min = 0.0333m³/s

t = 30s

Pₐ = 1.013bar absolute

P₁ = 8.0 + 1.013 = 9.013bar absolute

P₂ = 6.0 + 1.013 = 7.013bar absolute

ΔP = 2.0bar absolute

V = (0.0333 × 30 × 1.013) / 2.0 = 0.506m³ = 506L.

Theoretical minimum is about 500L, but a 2000L receiver is often selected for central screw plants because it also supports compressor cycling, dryer inlet cooling, condensate separation, and future expansion.

Worked example B, 10bar system: compressor delivers 18m³/min. Peak demand is 21m³/min for 60 seconds. Allowable swing from 10.0bar to 8.0bar.

Q = 3m³/min = 0.05m³/s

t = 60s

P₁ = 10.0 + 1.013 = 11.013bar absolute

P₂ = 8.0 + 1.013 = 9.013bar absolute

ΔP = 2.0bar absolute

V = (0.05 × 60 × 1.013) / 2.0 = 1.519m³ = 1519L.

A 2000L tank is appropriate, with larger volume if demand growth, humid climate, or strict pressure stability is expected.

Worked example C, load/unload cycle control: if the screw compressor must not exceed one load/unload cycle per 30 seconds, the receiver volume should be calculated from FAD, control differential, compressor inlet temperature, and receiver air temperature using the manufacturer’s cycle formula. In practice, 2000L is frequently used for 75–90kW-class fixed-speed screws, while 90kW and above may use 2000L plus extra dry storage .

Typical Specifications For 2000L Carbon Steel Receivers

Actual diameter, height, nozzle rating, head type, and weight must be confirmed from the fabricator drawing because plate thickness changes with pressure, temperature, steel grade, and corrosion allowance.

Carbon Steel Protection And When To Upgrade

Carbon steel is economical and strong, but compressed air condensate can be acidic when it contains oil aerosol, especially from oil-injected screw compressors. A 2000L wet receiver should therefore include internal corrosion protection.

• Bare carbon steel:​ only acceptable for dry, low-humidity, non-critical utility air with frequent inspection. Not recommended for humid wet storage.

• Internal epoxy coating:​ common for general screw plant air. Provides a smooth barrier against condensate and reduces rust particles entering filters and dryers .

• Hot-dip galvanizing:​ suitable for humid rooms, outdoor tanks, and sites with aggressive condensate. Zinc layer protects the steel substrate even if minor coating damage occurs .

• Food-grade or ALM-type internal coating:​ used where audit standards require enhanced hygiene in non-stainless loops .

• Stainless steel alternative:​ 304 for clean utility, 316/316L for coastal, chemical, washdown, pharmaceutical, and high-purity loops. A 2000L stainless receiver costs more but eliminates rust-flake contamination and improves cleanroom audit results.

External protection is equally important. Indoor tanks need primer and topcoat; outdoor tanks need UV-stable polyurethane or powder coat, drainage protection, and corrosion allowance for the environment.

Wet Receiver, Dry Receiver, And System Layout

For 2000L screw installations, the most reliable arrangements are:

1. Single wet receiver:​ aftercooler → moisture separator → 2000L carbon steel wet receiver → pre-filter → dryer → post-filter → distribution. Best for general plants where the dryer handles final drying and the large tank provides cooling, condensate separation, and compressor buffering.

2. Wet plus dry receivers:​ 2000L wet carbon steel tank before the dryer and 1000L or 2000L dry tank after the dryer. Best for packaging, food utility, paint, electronics, laboratories, and plants with intermittent high peaks. The wet tank reduces dryer load; the dry tank stabilizes treated air.

3. Dry-only receiver:​ compressor → aftercooler → filters → dryer → 2000L dry receiver. Suitable when upstream buffering is already provided by a smaller wet tank or when the plant mainly needs reserve of clean, low-dew-point air.

4. Local 2000L buffer:​ a large tank near a bottling line, blast cabinet, tire plant, CNC cluster, or centralized air station to cover local surges without disturbing the main header.

Filtration And Air Quality Integration

The receiver is not a filter. For screw systems, specify treatment according to ISO 8573-1 purity targets for water, particles, and oil.

• Aftercooler moisture separator with automatic drain before the wet receiver.

• Particulate pre-filter, typically 3–5 micron, to protect dryer coils, valves, and desiccant.

• Coalescing oil filter, commonly 0.01 micron for sensitive duty, to control oil aerosol.

• Refrigerated dryer for approximately +3°C to +10°C pressure dew point, or adsorption dryer for -20°C, -40°C, or -70°C depending on process.

• Desiccant dust post-filter, 1 micron standard; 0.01 micron for instruments, food, pharma, and electronics.

• Activated carbon filter for oil vapor, odor, and hydrocarbon trace removal where required.

• Stainless or coated dry receiver for hygienic loops, with sanitary terminals and documented filter records.

A 2000L wet carbon steel receiver improves dryer performance by lowering inlet temperature and removing bulk liquid. This reduces refrigeration load, desiccant saturation, filter pressure drop, and maintenance frequency.

Pressure Drop And Energy Management

The receiver itself has low intrinsic loss because internal velocity is intentionally low. System losses come from inlet nozzle, piping, isolation valves, moisture separator, filters, dryer, and distribution mains. For 2000L systems feeding large screw plants, keep main line velocity reasonable, size inlet/outlet flanges for design flow, and monitor filter differential pressure.

Energy benefits of correct 2000L storage include:

• Fixed-speed screw compressors: larger receiver extends load/unload cycles, reduces motor starts, and avoids repeated unloaded running.

• VSD screw compressors: receiver stabilizes transient peaks and allows narrower pressure band control.

• Dryer support: wet receiver cools air and removes condensate, reducing refrigeration or regeneration energy.

• Pressure band control: every unnecessary pressure increase raises compressor power. A 2000L buffer that holds tight, process-adequate pressure avoids artificial overpressurization.

• Drain management: automatic zero-loss or level-sensing drains remove condensate without wasting air. Timer drains should be set by actual condensate volume, not by short fixed intervals that may vent compressed air.

Safety, Relief, And Compliance

A 2000L air receiver is a pressure vessel and must be protected as follows:

1. Safety relief valve:​ at least one certified spring-loaded device sized to pass full compressor output and set at or below maximum allowable working pressure. Common industrial setpoint guidance is approximately 1.05–1.10 times working pressure; for an 8bar tank this often means about 8.4–8.8bar, subject to the responsible code . No isolating valve may be placed between the receiver and its relief device.

2. Pressure gauge:​ calibrated, visible, and ranged about 1.5–3.0 times working pressure so normal operation sits in the useful middle of the scale . An isolation valve for gauge replacement is acceptable if it does not isolate the tank from protection.

3. Bottom drain:​ manual drains are acceptable for small attended systems, but automatic zero-loss, electronic, or float drains are preferred for continuous 2000L screw plants. The drain must be at the lowest point to remove water and oil emulsion.

4. Code and documentation:​ specify ASME Section VIII Div.1 for North American projects, PED 2014/68/EU and EN 13445 for European projects, GB/T 150 or local special-equipment regulations for Chinese projects, and equivalent local rules elsewhere . Request fabrication drawings, material certificates, WPS/PQR weld procedure, NDT reports, hydrostatic test report, nameplate data, and inspection plan.

5. Relief discharge:​ route discharge vertically upward or to a safe outdoor location, away from walkways, electrical panels, and confined spaces.

6. Periodic inspection:​ follow local regulation. General industrial guidance suggests external inspection around every two years and internal inspection around every five years, adjusted for humidity, oil carryover, lining condition, and corrosivity . After repair, overpressure event, or service change, perform internal inspection, NDT, hydrostatic test, and recertification before return to service.

Installation Recommendations

• Place the 2000L wet receiver as close as practical to the aftercooler and moisture separator. Short, properly sized piping reduces re-entrainment and pressure drop.

• For vertical tanks, provide reinforced concrete foundation, anchor bolts, and vibration-isolated compressor connections. For horizontal tanks, provide saddle supports, level base, and seismic restraints where required.

• Maintain clearance for manhole/handhole access, drain service, relief valve discharge, gauge reading, and NDT thickness measurement.

• Verify passage width, door height, crane capacity, and rigging plan before delivering a 2000L tank; large vessels may exceed 350–465kg and require mechanical handling .

• For outdoor installation, use weatherproof coating or galvanized execution, heat-traced drain in freezing climates, and relief discharge above snow or flood level.

• For humid or oily screw air, specify automatic drain, epoxy or galvanized internal protection, and regular separator maintenance.

• Ground and bond the vessel according to electrical and process safety codes, especially in explosive atmospheres.

Inspection And Maintenance

• Daily or automatic: confirm drain operation, check gauge reading, verify no abnormal noise, leakage, or relief discharge.

• Weekly: inspect relief valve exterior, gauge accuracy, nozzle and support condition, coating or insulation condition.

• Monthly: review filter differentials, dryer dew point, condensate oil appearance, and automatic drain cycle.

• Periodic internal inspection: check bottom-plate thinning, sludge, rust, lining damage, weld roots, manhole gasket condition, and drain nozzle corrosion.

• Periodic external inspection: check coating, supports, foundation settlement, nozzle threads or flanges, nameplate legibility, and relief valve tag.

• Stainless upgrade loops: if the dry receiver is stainless, verify passivation, surface finish, gasket compatibility, and cleaning chemical suitability.

Application Recommendations

Common Problems And Corrective Actions

Procurement Specification Checklist

Request written data rather than verbal summaries.

• Compressor type: fixed-speed or VSD screw; free air delivery at working pressure; motor power only as supporting data.

• Peak demand profile: maximum instantaneous demand, average demand, event duration, allowable pressure swing.

• Required volume: 2000L as wet, dry, or split system; confirm with percentage rule and V = (Q × t × Pₐ) / (P₁ − P₂).

• Working pressure and design pressure: 8, 10, 13, or 16bar; cut-in and cut-out setpoints; relief valve setpoint.

• Air quality target: ISO 8573-1 water, particle, and oil classes; required pressure dew point; sterile or hygienic requirements.

• Material and protection: carbon steel grade, internal epoxy/galvanizing/food-grade lining, external coating, stainless option.

• Orientation and space: vertical or horizontal; foundation, anchoring, seismic data, passage and rigging clearance.

• Inlet conditions: aftercooler outlet temperature, ambient temperature, relative humidity, oil-injected or oil-free screw.

• Connections: threaded or flange sizes for inlet/outlet, drain, gauge, safety valve; manhole/handhole by code.

• Accessories: safety relief valve calculation, pressure gauge, automatic zero-loss drain, level indicator, transducer, communication.

• Standards and testing: ASME VIII, PED/EN, GB/T 150, or local equivalent; hydrostatic test pressure; NDT method; nameplate and inspection documents.

• Installation environment: indoor/outdoor, coastal, washdown, explosive area, ventilation, drainage, maintenance clearance.

Frequently Asked Questions

Q1: Which screw compressor size fits a 2000L carbon steel receiver?

For fixed-speed screws with stable demand, 2000L covers roughly 13–20m³/min at 10–15 percent rule and about 10m³/min at 20 percent rule . For strongly fluctuating demand, use the peak-buffer formula rather than a fixed percentage. For VSD screws, the same tank may serve larger nominal FAD because the drive modulates flow, but local peaks still determine final volume.

Q2: Is carbon steel suitable for a 2000L wet receiver?

Yes, for general plant air. The wet receiver handles saturated air and condensate, so specify internal epoxy, hot-dip galvanizing, or food-grade lining depending on humidity, oil carryover, and audit requirements . Bare carbon steel is not recommended in humid or oily wet service because condensate accelerates rust and can send particles into filters and dryers.

Q3: Should the 2000L tank be installed before or after the dryer?

For most central screw plants, install a 2000L wet receiver before the dryer for cooling and condensate separation, then add a dry receiver after the dryer for stable treated air. If only one tank is used, place it before the dryer for general utility and after the dryer only when the entire upstream air is already filtered and dried.

Q4: What safety devices are mandatory on a 2000L receiver?

At minimum, a calibrated pressure gauge, one or more certified safety relief valves sized for system flow, and a bottom drain. Depending on code, add pressure transmitter, temperature probe, condensate level alarm, and remote monitoring. No valve may isolate the relief device from the tank . Relief setpoint is commonly 1.05–1.10 times working pressure within the allowable code margin .

Q5: How often should condensate be drained from a 2000L tank?

Automatic zero-loss or level-sensing drains are preferred for continuous screw plants. In high humidity, check or operate drains daily. In normal workshop duty, automatic drain with weekly inspection is usually sufficient. Manual drains should be opened frequently enough to prevent liquid accumulation. All lubricated-compressor condensate should pass through an oil-water separator before disposal.

Q6: Can a 2000L 8bar tank be used at 10bar or 13bar?

Only if the vessel nameplate, design pressure, shell thickness, relief devices, flanges, and code documentation support the higher pressure. A tank stamped 8bar must not be operated at 10bar or 13bar without recalculation and recertification by a qualified pressure-vessel engineer.

Q7: What coating is best for humid or outdoor screw air storage?

Hot-dip galvanizing or external polyurethane with internal epoxy is common for outdoor and humid service . For coastal, chemical, or washdown sites, consider stainless 304/316L instead of carbon steel. For food and pharmaceutical utility, use food-grade internal coating or stainless with documented surface finish.

Q8: How does a 2000L receiver reduce energy consumption?

It extends load/unload time for fixed-speed screws, reduces starts, supports narrower VSD pressure band, cools dryer inlet air, removes bulk condensate, and prevents unnecessary pressure increase. Proper automatic drainage also avoids air loss compared with open manual drains.

Final Selection Recommendation

Specify a 2000L carbon steel air receiver by actual screw free air delivery, peak demand profile, allowable pressure swing, working pressure, inlet temperature, humidity, air quality class, and local pressure-vessel code rather than by motor power alone. For stable central screw plants, start with 10–20 percent of FAD, confirm with V = (Q × t × Pₐ) / (P₁ − P₂), and select 8/10/13/16bar construction according to compressor cut-out and safety requirement. Use internal epoxy, galvanizing, or food-grade lining for wet storage; use stainless 304/316L when hygiene, corrosion, or contamination control justifies the upgrade. Install the 2000L tank as a wet receiver before the dryer for cooling and condensate separation, add a dry receiver after the dryer for sensitive production, and equip every vessel with code-compliant relief protection, accurate pressure indication, automatic bottom drainage, and a planned internal/external inspection program. With correct volume, carbon steel protection, and safety configuration, the 2000L receiver improves screw compressor stability, reduces cycling and energy waste, protects filters and dryers, and provides reliable reserve air for large industrial compressed air networks.